|Blade Length||165 mm|
|Blade Height||49 mm|
|Blade Thickness Above Heel||3 mm|
|Steel Type||Aogami #2 (Blue Carbon Steel) with Stainless Steel Cladding|
|Handle||Wa (Japanese) Handle - Oval Burnt Chestnut Plastic Collar|
|Knife Line||Fujimoto Nashiji|
|Made in||Tsubame-Sanjo, Niigata, Japan|
A note about measurements: Handmade Japanese knives can vary in their dimensions, so these measurements are only an example.
About the Shape - Under utilized in the western kitchen, the nakiri’s flatter blade is meant for the push/pull chopping of vegetables. Since the entire flat edge of the knife touches the cutting board at once, you wont be turning the vegetable into an 'accordion', still connected like a paper doll after you've cut them. The added weight of the blade allow it to fall through food more easily while you chop, so the knife does more of the work for you!
About Fujimoto Nashiji - The Fujimoto Nashiji achieves a great balance in knife making; extremely high performance, along with minimal maintenance. The Aogami #2 (#2 blue Steel) carbon steel core of the blade has been clad (wrapped) in stainless steel. This allows you to get the performance of traditional high-carbon steel, but only the edge of the knife requires the extra attention and drying that carbon steel asks of you, not the whole knife. This type of construction is our favourite type of knife construction because it gives a long lasting edge and also easier maintenance than a full-carbon steel knife.
The finish on this line is called nashiji, named for its resemblance to the skin of an Asian pear. The scorched chestnut handles offer a classic rustic look, and the scorched finish on the wood lends durability to the handle.
Carbon steel gets crazy sharp and holds an edge very well, but can rust. Stainless steel has the benefit of being less prone to rust but isn’t quite as sharp. Luckily, Japan has the solution. They make lots of kitchen knives by sandwiching 3 layers of steel together. In the case of kitchen knives the softer, outside layer is stainless and the hard core is carbon steel. The best of both worlds, super sharp — with low hassle. These are some of the most popular knives we sell. The exposed core steel can rust, and you have to wipe it dry to keep that from happening, but this is only a small part of the knife. Over time, the edge will oxidize from from shiny to a dull grey, this oxide layer slows down rust.
• Only cut food you can bite through with this knife. Hard foods can chip the blade. No olive pits, bones, lobster shells, woody stems or parmesan rinds. Cutting frozen food is especially bad because the cold will make hard steel even more brittle. If you wouldn’t chew it with your own teeth, don’t cut it.
• Your cutting surface is the biggest culprit of dulling your knife. Use wood. End grain wood is especially good. Plastic can be fine too, but certainly not glass, granite or bamboo.
• The edge of your knife works best sliding forwards or backwards. Scraping the knife edge sideways will dull or damage the edge. Instead, use the spine of the knife to move foods across the cutting board. Do not twist the edge or pry with the edge, this is the worst screwdriver you ever bought and these motions will certainly damage the edge. Listen to the knife! If you can hear the edge making a “tink” sound on the cutting board, change what you are doing.
• After use, wash the knife by hand with regular dish soap, rinse with hot water and dry by hand immediately. Dishwashers are very bad for knives.
• Wood handles may dry out over time and exposure to water. Simply treat them with some food safe mineral oil or beeswax.
• If you see orange rust, remove it. The scrubby side of a sponge can do the trick. If it’s still not coming off try baking soda and water mixed into a paste or a product called Barkeeper’s Friend.
• Protect the edge; for your safety and to avoid edge damage. A simple blade cover will do the trick if you keep knives in a drawer or travel case.
• A convenient wall magnet made with wood is a great way to show off your knives. Be sure to put it back spine first, then roll it onto the blade face. This will keep the edge from contacting the wood first.
• The good-ol’ counter top block can keep knives at the ready and protected. So can drawer inserts. Whatever the method, keep the edge from touching anything else.
We aim to ship your order within 1 business day at Knifewear, if there is a hold up, we'll aim to let you know and give you a timeline.
We offer free shippingon orders over $100* anywhere in Canada and $200* to customers in the USA. We ship worldwide, and offer up to the minute rates from our shipping partner DHL.
*Konro Grills and some other larger items are excluded from the free shipping offer.
How do I make a return on an online order?
No worries, we've got you sorted. Head over to https://knifewear.com/returns and follow the prompts.
Can I pick up my order Curbside / At the store?
Absolutely, as long as all the items you are looking for are in stock at the location you want to pickup from, you'll be able to select that at the checkout. If one or more items aren't at your preferred location we are happy to ship it to you.